id
stringlengths 11
11
| image
stringlengths 22
22
| conversations
listlengths 2
2
|
|---|---|---|
Shaft_00668
|
images/Shaft_00668.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø35.4 mm and length at least 70.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø33.4 mm over length 14.4 mm (from Z=0.0 to Z=14.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø33.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 51.1 mm (from Z=0.0 to Z=51.1).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00282
|
images/Shaft_00282.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø40.5 mm and length at least 302.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø38.5 mm over length 74.6 mm (from Z=0.0 to Z=74.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø38.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.8 mm over length 46.6 mm (from Z=0.0 to Z=223.2).\n10. Finish turn diameter Ø30.0 mm over length 176.6 mm (from Z=0.0 to Z=176.6).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00939
|
images/Shaft_00939.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 75.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 33.1 mm (from Z=0.0 to Z=33.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø20.1 mm over length 37.6 mm (from Z=0.0 to Z=37.6).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00944
|
images/Shaft_00944.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø81.5 mm and length at least 257.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø79.5 mm over length 20.2 mm (from Z=0.0 to Z=20.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø79.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø63.2 mm over length 64.5 mm (from Z=0.0 to Z=232.4).\n10. Finish turn diameter Ø52.9 mm over length 26.7 mm (from Z=0.0 to Z=167.9).\n11. Finish turn diameter Ø33.4 mm over length 37.7 mm (from Z=0.0 to Z=141.2).\n12. Finish turn diameter Ø30.0 mm over length 103.5 mm (from Z=0.0 to Z=103.5).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00606
|
images/Shaft_00606.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.0 mm and length at least 205.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 100.5 mm (from Z=0.0 to Z=100.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø18.8 mm over length 99.9 mm (from Z=0.0 to Z=99.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00959
|
images/Shaft_00959.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø36.4 mm and length at least 305.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø34.4 mm over length 101.5 mm (from Z=0.0 to Z=101.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø34.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 199.0 mm (from Z=0.0 to Z=199.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00934
|
images/Shaft_00934.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø74.5 mm and length at least 190.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø72.5 mm over length 54.9 mm (from Z=0.0 to Z=54.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø72.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø65.3 mm over length 70.4 mm (from Z=0.0 to Z=130.9).\n9. Finish turn diameter Ø61.5 mm over length 42.5 mm (from Z=0.0 to Z=60.5).\n10. Finish turn diameter Ø47.6 mm over length 18.0 mm (from Z=0.0 to Z=18.0).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00731
|
images/Shaft_00731.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø42.5 mm and length at least 149.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø40.5 mm over length 33.6 mm (from Z=0.0 to Z=33.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø40.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 111.0 mm (from Z=0.0 to Z=111.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00287
|
images/Shaft_00287.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø35.1 mm and length at least 215.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø33.1 mm over length 38.4 mm (from Z=0.0 to Z=38.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø33.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 172.4 mm (from Z=0.0 to Z=172.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00527
|
images/Shaft_00527.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.0 mm and length at least 303.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 279.6 mm (from Z=0.0 to Z=279.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø27.3 mm over length 18.6 mm (from Z=0.0 to Z=18.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00807
|
images/Shaft_00807.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø67.9 mm and length at least 321.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø65.9 mm over length 60.8 mm (from Z=0.0 to Z=60.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø65.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø59.5 mm over length 85.8 mm (from Z=0.0 to Z=256.0).\n10. Finish turn diameter Ø40.5 mm over length 29.9 mm (from Z=0.0 to Z=170.2).\n11. Finish turn diameter Ø30.0 mm over length 140.3 mm (from Z=0.0 to Z=140.3).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00229
|
images/Shaft_00229.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø37.4 mm and length at least 110.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø35.4 mm over length 5.0 mm (from Z=0.0 to Z=5.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø35.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 100.9 mm (from Z=0.0 to Z=100.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00436
|
images/Shaft_00436.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø51.8 mm and length at least 320.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø49.8 mm over length 47.0 mm (from Z=0.0 to Z=47.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø49.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø40.8 mm over length 126.1 mm (from Z=0.0 to Z=268.2).\n10. Finish turn diameter Ø31.5 mm over length 33.7 mm (from Z=0.0 to Z=142.1).\n11. Finish turn diameter Ø30.0 mm over length 108.4 mm (from Z=0.0 to Z=108.4).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00028
|
images/Shaft_00028.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø74.2 mm and length at least 137.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø72.2 mm over length 12.9 mm (from Z=0.0 to Z=12.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø72.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø65.1 mm over length 33.0 mm (from Z=0.0 to Z=119.1).\n9. Finish turn diameter Ø45.3 mm over length 30.2 mm (from Z=0.0 to Z=86.1).\n10. Finish turn diameter Ø30.0 mm over length 55.9 mm (from Z=0.0 to Z=55.9).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00374
|
images/Shaft_00374.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø61.0 mm and length at least 296.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø59.0 mm over length 29.1 mm (from Z=0.0 to Z=29.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø59.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø42.8 mm over length 100.1 mm (from Z=0.0 to Z=261.9).\n10. Finish turn diameter Ø30.0 mm over length 161.8 mm (from Z=0.0 to Z=161.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00819
|
images/Shaft_00819.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø52.3 mm and length at least 96.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø50.3 mm over length 16.0 mm (from Z=0.0 to Z=16.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø50.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø35.9 mm over length 26.8 mm (from Z=0.0 to Z=75.7).\n9. Finish turn diameter Ø30.1 mm over length 12.8 mm (from Z=0.0 to Z=48.9).\n10. Finish turn diameter Ø30.0 mm over length 36.1 mm (from Z=0.0 to Z=36.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00316
|
images/Shaft_00316.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø56.8 mm and length at least 274.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø54.8 mm over length 35.3 mm (from Z=0.0 to Z=35.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø54.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø35.7 mm over length 37.7 mm (from Z=0.0 to Z=234.6).\n10. Finish turn diameter Ø30.0 mm over length 196.9 mm (from Z=0.0 to Z=196.9).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00560
|
images/Shaft_00560.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø80.8 mm and length at least 305.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø78.8 mm over length 89.7 mm (from Z=0.0 to Z=89.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø78.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø69.4 mm over length 13.5 mm (from Z=0.0 to Z=210.6).\n10. Finish turn diameter Ø51.4 mm over length 55.5 mm (from Z=0.0 to Z=197.1).\n11. Finish turn diameter Ø39.4 mm over length 51.6 mm (from Z=0.0 to Z=141.6).\n12. Finish turn diameter Ø31.8 mm over length 90.0 mm (from Z=0.0 to Z=90.0).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00241
|
images/Shaft_00241.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø67.0 mm and length at least 318.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø65.0 mm over length 84.1 mm (from Z=0.0 to Z=84.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø65.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø56.5 mm over length 71.2 mm (from Z=0.0 to Z=229.8).\n10. Finish turn diameter Ø51.7 mm over length 61.2 mm (from Z=0.0 to Z=158.6).\n11. Finish turn diameter Ø39.3 mm over length 13.4 mm (from Z=0.0 to Z=97.4).\n12. Finish turn diameter Ø33.5 mm over length 84.0 mm (from Z=0.0 to Z=84.0).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00149
|
images/Shaft_00149.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø67.7 mm and length at least 172.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø65.7 mm over length 62.5 mm (from Z=0.0 to Z=62.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø65.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø62.3 mm over length 57.5 mm (from Z=0.0 to Z=104.8).\n9. Finish turn diameter Ø58.6 mm over length 47.3 mm (from Z=0.0 to Z=47.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00516
|
images/Shaft_00516.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø48.2 mm and length at least 257.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø46.2 mm over length 58.8 mm (from Z=0.0 to Z=58.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø46.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø38.2 mm over length 64.8 mm (from Z=0.0 to Z=193.2).\n10. Finish turn diameter Ø30.0 mm over length 128.4 mm (from Z=0.0 to Z=128.4).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00417
|
images/Shaft_00417.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø43.2 mm and length at least 301.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø41.2 mm over length 67.3 mm (from Z=0.0 to Z=67.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø41.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 229.6 mm (from Z=0.0 to Z=229.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00660
|
images/Shaft_00660.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø69.9 mm and length at least 103.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø67.9 mm over length 18.1 mm (from Z=0.0 to Z=18.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø67.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø50.2 mm over length 9.3 mm (from Z=0.0 to Z=79.9).\n9. Finish turn diameter Ø38.9 mm over length 29.6 mm (from Z=0.0 to Z=70.6).\n10. Finish turn diameter Ø30.0 mm over length 41.0 mm (from Z=0.0 to Z=41.0).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00198
|
images/Shaft_00198.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø45.2 mm and length at least 284.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø43.2 mm over length 68.8 mm (from Z=0.0 to Z=68.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø43.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø36.8 mm over length 9.3 mm (from Z=0.0 to Z=211.1).\n10. Finish turn diameter Ø30.0 mm over length 201.8 mm (from Z=0.0 to Z=201.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00585
|
images/Shaft_00585.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø48.9 mm and length at least 254.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø46.9 mm over length 81.1 mm (from Z=0.0 to Z=81.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø46.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø33.2 mm over length 58.3 mm (from Z=0.0 to Z=168.6).\n10. Finish turn diameter Ø30.0 mm over length 110.3 mm (from Z=0.0 to Z=110.3).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00325
|
images/Shaft_00325.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.0 mm and length at least 247.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 152.4 mm (from Z=0.0 to Z=152.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø21.7 mm over length 90.3 mm (from Z=0.0 to Z=90.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00823
|
images/Shaft_00823.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø47.4 mm and length at least 99.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø45.4 mm over length 5.0 mm (from Z=0.0 to Z=5.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø45.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 89.4 mm (from Z=0.0 to Z=89.4).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00702
|
images/Shaft_00702.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø42.0 mm and length at least 223.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø40.0 mm over length 40.4 mm (from Z=0.0 to Z=40.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø40.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø33.6 mm over length 147.2 mm (from Z=0.0 to Z=177.7).\n10. Finish turn diameter Ø30.0 mm over length 30.5 mm (from Z=0.0 to Z=30.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00949
|
images/Shaft_00949.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø62.1 mm and length at least 213.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø60.1 mm over length 49.7 mm (from Z=0.0 to Z=49.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø60.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø53.6 mm over length 56.3 mm (from Z=0.0 to Z=158.3).\n10. Finish turn diameter Ø38.1 mm over length 32.2 mm (from Z=0.0 to Z=102.0).\n11. Finish turn diameter Ø30.0 mm over length 69.8 mm (from Z=0.0 to Z=69.8).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00515
|
images/Shaft_00515.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø64.1 mm and length at least 186.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø62.1 mm over length 94.3 mm (from Z=0.0 to Z=94.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø62.1 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø52.2 mm over length 68.3 mm (from Z=0.0 to Z=87.6).\n9. Finish turn diameter Ø44.0 mm over length 19.3 mm (from Z=0.0 to Z=19.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00864
|
images/Shaft_00864.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø59.2 mm and length at least 132.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø57.2 mm over length 41.5 mm (from Z=0.0 to Z=41.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø57.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø51.2 mm over length 24.7 mm (from Z=0.0 to Z=86.3).\n9. Finish turn diameter Ø41.1 mm over length 12.5 mm (from Z=0.0 to Z=61.6).\n10. Finish turn diameter Ø30.0 mm over length 49.1 mm (from Z=0.0 to Z=49.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00836
|
images/Shaft_00836.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 151.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 92.7 mm (from Z=0.0 to Z=92.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø19.0 mm over length 53.3 mm (from Z=0.0 to Z=53.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00877
|
images/Shaft_00877.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø67.7 mm and length at least 257.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø65.7 mm over length 142.1 mm (from Z=0.0 to Z=142.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø65.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø53.1 mm over length 56.3 mm (from Z=0.0 to Z=110.1).\n10. Finish turn diameter Ø38.4 mm over length 53.8 mm (from Z=0.0 to Z=53.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00359
|
images/Shaft_00359.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.9 mm and length at least 88.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.9 mm over length 30.5 mm (from Z=0.0 to Z=30.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 53.1 mm (from Z=0.0 to Z=53.1).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00594
|
images/Shaft_00594.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø69.0 mm and length at least 299.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø67.0 mm over length 187.7 mm (from Z=0.0 to Z=187.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø67.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø55.5 mm over length 35.4 mm (from Z=0.0 to Z=106.4).\n10. Finish turn diameter Ø52.4 mm over length 71.0 mm (from Z=0.0 to Z=71.0).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00788
|
images/Shaft_00788.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø58.5 mm and length at least 89.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø56.5 mm over length 18.3 mm (from Z=0.0 to Z=18.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø56.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø37.9 mm over length 12.7 mm (from Z=0.0 to Z=66.1).\n9. Finish turn diameter Ø32.8 mm over length 53.4 mm (from Z=0.0 to Z=53.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00188
|
images/Shaft_00188.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø63.4 mm and length at least 149.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø61.4 mm over length 53.3 mm (from Z=0.0 to Z=53.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø61.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø53.0 mm over length 33.8 mm (from Z=0.0 to Z=91.4).\n9. Finish turn diameter Ø43.5 mm over length 57.6 mm (from Z=0.0 to Z=57.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00066
|
images/Shaft_00066.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 193.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 146.3 mm (from Z=0.0 to Z=146.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø24.9 mm over length 42.2 mm (from Z=0.0 to Z=42.2).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00355
|
images/Shaft_00355.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø80.2 mm and length at least 137.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø78.2 mm over length 26.0 mm (from Z=0.0 to Z=26.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø78.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø63.9 mm over length 5.0 mm (from Z=0.0 to Z=106.5).\n9. Finish turn diameter Ø50.4 mm over length 39.5 mm (from Z=0.0 to Z=101.5).\n10. Finish turn diameter Ø47.2 mm over length 7.5 mm (from Z=0.0 to Z=62.0).\n11. Finish turn diameter Ø39.8 mm over length 27.1 mm (from Z=0.0 to Z=54.5).\n12. Finish turn diameter Ø30.0 mm over length 27.4 mm (from Z=0.0 to Z=27.4).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00799
|
images/Shaft_00799.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø81.3 mm and length at least 310.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø79.3 mm over length 79.6 mm (from Z=0.0 to Z=79.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø79.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø72.3 mm over length 163.1 mm (from Z=0.0 to Z=226.1).\n10. Finish turn diameter Ø57.1 mm over length 63.0 mm (from Z=0.0 to Z=63.0).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00902
|
images/Shaft_00902.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø50.7 mm and length at least 137.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø48.7 mm over length 28.4 mm (from Z=0.0 to Z=28.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø48.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 103.6 mm (from Z=0.0 to Z=103.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00920
|
images/Shaft_00920.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø43.5 mm and length at least 101.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø41.5 mm over length 32.7 mm (from Z=0.0 to Z=32.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø41.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø37.5 mm over length 5.4 mm (from Z=0.0 to Z=63.3).\n9. Finish turn diameter Ø30.0 mm over length 57.9 mm (from Z=0.0 to Z=57.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00942
|
images/Shaft_00942.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø62.9 mm and length at least 198.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø60.9 mm over length 29.6 mm (from Z=0.0 to Z=29.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø60.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø41.6 mm over length 38.3 mm (from Z=0.0 to Z=164.2).\n10. Finish turn diameter Ø30.0 mm over length 125.9 mm (from Z=0.0 to Z=125.9).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00330
|
images/Shaft_00330.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø41.9 mm and length at least 311.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø39.9 mm over length 69.8 mm (from Z=0.0 to Z=69.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø39.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 236.2 mm (from Z=0.0 to Z=236.2).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00727
|
images/Shaft_00727.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø78.7 mm and length at least 250.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø76.7 mm over length 146.5 mm (from Z=0.0 to Z=146.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø76.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø71.0 mm over length 59.0 mm (from Z=0.0 to Z=99.4).\n10. Finish turn diameter Ø55.0 mm over length 40.4 mm (from Z=0.0 to Z=40.4).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00396
|
images/Shaft_00396.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø33.9 mm and length at least 116.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø31.9 mm over length 6.1 mm (from Z=0.0 to Z=6.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø31.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 105.5 mm (from Z=0.0 to Z=105.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00463
|
images/Shaft_00463.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø50.9 mm and length at least 186.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø48.9 mm over length 36.5 mm (from Z=0.0 to Z=36.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø48.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø41.0 mm over length 17.2 mm (from Z=0.0 to Z=145.3).\n10. Finish turn diameter Ø30.0 mm over length 128.1 mm (from Z=0.0 to Z=128.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00393
|
images/Shaft_00393.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø71.8 mm and length at least 315.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø69.8 mm over length 85.7 mm (from Z=0.0 to Z=85.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø69.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø51.3 mm over length 73.6 mm (from Z=0.0 to Z=224.7).\n10. Finish turn diameter Ø38.5 mm over length 56.1 mm (from Z=0.0 to Z=151.1).\n11. Finish turn diameter Ø30.0 mm over length 95.0 mm (from Z=0.0 to Z=95.0).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00311
|
images/Shaft_00311.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 280.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 202.7 mm (from Z=0.0 to Z=202.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø25.3 mm over length 72.9 mm (from Z=0.0 to Z=72.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00680
|
images/Shaft_00680.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø77.9 mm and length at least 90.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø75.9 mm over length 7.8 mm (from Z=0.0 to Z=7.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø75.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø64.2 mm over length 17.6 mm (from Z=0.0 to Z=77.6).\n9. Finish turn diameter Ø48.6 mm over length 10.3 mm (from Z=0.0 to Z=60.0).\n10. Finish turn diameter Ø33.8 mm over length 23.9 mm (from Z=0.0 to Z=49.7).\n11. Finish turn diameter Ø30.0 mm over length 25.8 mm (from Z=0.0 to Z=25.8).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00744
|
images/Shaft_00744.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø69.1 mm and length at least 318.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø67.1 mm over length 56.3 mm (from Z=0.0 to Z=56.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø67.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø52.5 mm over length 49.5 mm (from Z=0.0 to Z=256.9).\n10. Finish turn diameter Ø32.9 mm over length 49.0 mm (from Z=0.0 to Z=207.4).\n11. Finish turn diameter Ø30.0 mm over length 158.4 mm (from Z=0.0 to Z=158.4).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00921
|
images/Shaft_00921.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø36.9 mm and length at least 110.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø34.9 mm over length 10.9 mm (from Z=0.0 to Z=10.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø34.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 94.6 mm (from Z=0.0 to Z=94.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00461
|
images/Shaft_00461.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø79.1 mm and length at least 142.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø77.1 mm over length 59.9 mm (from Z=0.0 to Z=59.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø77.1 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø73.5 mm over length 28.1 mm (from Z=0.0 to Z=77.6).\n9. Finish turn diameter Ø69.8 mm over length 49.5 mm (from Z=0.0 to Z=49.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00522
|
images/Shaft_00522.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø71.7 mm and length at least 102.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø69.7 mm over length 28.8 mm (from Z=0.0 to Z=28.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø69.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø64.9 mm over length 14.5 mm (from Z=0.0 to Z=68.5).\n9. Finish turn diameter Ø58.0 mm over length 30.9 mm (from Z=0.0 to Z=54.0).\n10. Finish turn diameter Ø40.7 mm over length 23.1 mm (from Z=0.0 to Z=23.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00631
|
images/Shaft_00631.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø48.2 mm and length at least 121.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø46.2 mm over length 10.8 mm (from Z=0.0 to Z=10.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø46.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø34.4 mm over length 25.9 mm (from Z=0.0 to Z=105.3).\n9. Finish turn diameter Ø30.0 mm over length 79.4 mm (from Z=0.0 to Z=79.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00490
|
images/Shaft_00490.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.0 mm and length at least 233.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 196.6 mm (from Z=0.0 to Z=196.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø23.4 mm over length 31.6 mm (from Z=0.0 to Z=31.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00195
|
images/Shaft_00195.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø51.6 mm and length at least 226.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø49.6 mm over length 43.2 mm (from Z=0.0 to Z=43.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø49.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø43.5 mm over length 20.1 mm (from Z=0.0 to Z=178.6).\n10. Finish turn diameter Ø36.1 mm over length 46.5 mm (from Z=0.0 to Z=158.5).\n11. Finish turn diameter Ø32.7 mm over length 45.8 mm (from Z=0.0 to Z=112.0).\n12. Finish turn diameter Ø30.0 mm over length 66.2 mm (from Z=0.0 to Z=66.2).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00256
|
images/Shaft_00256.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø72.0 mm and length at least 145.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø70.0 mm over length 13.7 mm (from Z=0.0 to Z=13.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø70.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø55.7 mm over length 18.4 mm (from Z=0.0 to Z=127.1).\n9. Finish turn diameter Ø47.2 mm over length 108.7 mm (from Z=0.0 to Z=108.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00693
|
images/Shaft_00693.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 220.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 168.4 mm (from Z=0.0 to Z=168.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø26.0 mm over length 46.9 mm (from Z=0.0 to Z=46.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00740
|
images/Shaft_00740.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 239.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 220.6 mm (from Z=0.0 to Z=220.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø26.9 mm over length 13.8 mm (from Z=0.0 to Z=13.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00577
|
images/Shaft_00577.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø68.5 mm and length at least 270.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø66.5 mm over length 129.9 mm (from Z=0.0 to Z=129.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø66.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø62.3 mm over length 76.0 mm (from Z=0.0 to Z=135.1).\n10. Finish turn diameter Ø50.9 mm over length 59.1 mm (from Z=0.0 to Z=59.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00157
|
images/Shaft_00157.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø70.6 mm and length at least 96.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø68.6 mm over length 33.1 mm (from Z=0.0 to Z=33.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø68.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø48.8 mm over length 22.4 mm (from Z=0.0 to Z=58.6).\n9. Finish turn diameter Ø44.3 mm over length 13.4 mm (from Z=0.0 to Z=36.2).\n10. Finish turn diameter Ø30.0 mm over length 22.8 mm (from Z=0.0 to Z=22.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00612
|
images/Shaft_00612.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø81.5 mm and length at least 153.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø79.5 mm over length 20.5 mm (from Z=0.0 to Z=20.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø79.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø76.4 mm over length 41.5 mm (from Z=0.0 to Z=127.8).\n9. Finish turn diameter Ø68.8 mm over length 10.8 mm (from Z=0.0 to Z=86.3).\n10. Finish turn diameter Ø62.4 mm over length 29.5 mm (from Z=0.0 to Z=75.5).\n11. Finish turn diameter Ø52.3 mm over length 34.3 mm (from Z=0.0 to Z=46.0).\n12. Finish turn diameter Ø33.4 mm over length 11.7 mm (from Z=0.0 to Z=11.7).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00392
|
images/Shaft_00392.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø62.8 mm and length at least 91.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø60.8 mm over length 14.6 mm (from Z=0.0 to Z=14.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø60.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø50.5 mm over length 42.4 mm (from Z=0.0 to Z=71.5).\n9. Finish turn diameter Ø39.9 mm over length 29.1 mm (from Z=0.0 to Z=29.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00969
|
images/Shaft_00969.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø76.9 mm and length at least 275.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø74.9 mm over length 124.6 mm (from Z=0.0 to Z=124.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø74.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø65.4 mm over length 23.6 mm (from Z=0.0 to Z=145.5).\n10. Finish turn diameter Ø59.0 mm over length 121.9 mm (from Z=0.0 to Z=121.9).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00688
|
images/Shaft_00688.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø56.2 mm and length at least 324.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø54.2 mm over length 78.8 mm (from Z=0.0 to Z=78.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø54.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø34.9 mm over length 27.0 mm (from Z=0.0 to Z=240.4).\n10. Finish turn diameter Ø30.0 mm over length 213.4 mm (from Z=0.0 to Z=213.4).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00361
|
images/Shaft_00361.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø56.6 mm and length at least 306.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø54.6 mm over length 26.3 mm (from Z=0.0 to Z=26.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø54.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø47.4 mm over length 63.7 mm (from Z=0.0 to Z=274.7).\n10. Finish turn diameter Ø42.2 mm over length 98.3 mm (from Z=0.0 to Z=211.0).\n11. Finish turn diameter Ø30.0 mm over length 112.7 mm (from Z=0.0 to Z=112.7).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00816
|
images/Shaft_00816.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø52.9 mm and length at least 143.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø50.9 mm over length 17.6 mm (from Z=0.0 to Z=17.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø50.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø31.7 mm over length 42.1 mm (from Z=0.0 to Z=120.8).\n9. Finish turn diameter Ø30.0 mm over length 78.7 mm (from Z=0.0 to Z=78.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00401
|
images/Shaft_00401.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø71.8 mm and length at least 321.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø69.8 mm over length 63.2 mm (from Z=0.0 to Z=63.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø69.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø65.9 mm over length 61.8 mm (from Z=0.0 to Z=252.9).\n10. Finish turn diameter Ø60.2 mm over length 47.1 mm (from Z=0.0 to Z=191.1).\n11. Finish turn diameter Ø52.3 mm over length 70.5 mm (from Z=0.0 to Z=144.0).\n12. Finish turn diameter Ø44.3 mm over length 47.6 mm (from Z=0.0 to Z=73.5).\n13. Finish turn diameter Ø35.7 mm over length 25.9 mm (from Z=0.0 to Z=25.9).\n14. Break all edges (e.g., 2×45° where applicable).\n15. Remove the workpiece from the lathe."
}
] |
Shaft_00092
|
images/Shaft_00092.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø73.6 mm and length at least 141.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø71.6 mm over length 40.8 mm (from Z=0.0 to Z=40.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø71.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø54.4 mm over length 12.1 mm (from Z=0.0 to Z=95.3).\n9. Finish turn diameter Ø49.5 mm over length 5.6 mm (from Z=0.0 to Z=83.2).\n10. Finish turn diameter Ø31.2 mm over length 37.4 mm (from Z=0.0 to Z=77.6).\n11. Finish turn diameter Ø30.0 mm over length 40.2 mm (from Z=0.0 to Z=40.2).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00917
|
images/Shaft_00917.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø34.1 mm and length at least 210.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø32.1 mm over length 65.2 mm (from Z=0.0 to Z=65.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø32.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 140.4 mm (from Z=0.0 to Z=140.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00489
|
images/Shaft_00489.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø74.2 mm and length at least 295.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø72.2 mm over length 28.4 mm (from Z=0.0 to Z=28.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø72.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø52.9 mm over length 48.5 mm (from Z=0.0 to Z=262.1).\n10. Finish turn diameter Ø43.9 mm over length 98.5 mm (from Z=0.0 to Z=213.6).\n11. Finish turn diameter Ø30.3 mm over length 86.5 mm (from Z=0.0 to Z=115.1).\n12. Finish turn diameter Ø30.0 mm over length 28.6 mm (from Z=0.0 to Z=28.6).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00451
|
images/Shaft_00451.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø74.7 mm and length at least 300.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø72.7 mm over length 24.7 mm (from Z=0.0 to Z=24.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø72.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø61.5 mm over length 91.9 mm (from Z=0.0 to Z=270.9).\n10. Finish turn diameter Ø43.4 mm over length 31.9 mm (from Z=0.0 to Z=179.0).\n11. Finish turn diameter Ø30.0 mm over length 147.1 mm (from Z=0.0 to Z=147.1).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00251
|
images/Shaft_00251.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø75.0 mm and length at least 304.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø73.0 mm over length 54.7 mm (from Z=0.0 to Z=54.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø73.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø63.5 mm over length 52.3 mm (from Z=0.0 to Z=244.9).\n10. Finish turn diameter Ø45.1 mm over length 35.4 mm (from Z=0.0 to Z=192.6).\n11. Finish turn diameter Ø37.4 mm over length 84.3 mm (from Z=0.0 to Z=157.2).\n12. Finish turn diameter Ø30.0 mm over length 72.9 mm (from Z=0.0 to Z=72.9).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00653
|
images/Shaft_00653.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 152.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 102.6 mm (from Z=0.0 to Z=102.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø29.6 mm over length 44.6 mm (from Z=0.0 to Z=44.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00769
|
images/Shaft_00769.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø79.5 mm and length at least 311.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø77.5 mm over length 70.8 mm (from Z=0.0 to Z=70.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø77.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø73.3 mm over length 123.9 mm (from Z=0.0 to Z=236.1).\n10. Finish turn diameter Ø58.2 mm over length 112.2 mm (from Z=0.0 to Z=112.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00670
|
images/Shaft_00670.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø38.1 mm and length at least 108.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø36.1 mm over length 21.6 mm (from Z=0.0 to Z=21.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø36.1 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 82.3 mm (from Z=0.0 to Z=82.3).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00129
|
images/Shaft_00129.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø40.0 mm and length at least 213.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø38.0 mm over length 21.6 mm (from Z=0.0 to Z=21.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø38.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 187.2 mm (from Z=0.0 to Z=187.2).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00637
|
images/Shaft_00637.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø40.7 mm and length at least 119.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø38.7 mm over length 27.7 mm (from Z=0.0 to Z=27.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø38.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 86.8 mm (from Z=0.0 to Z=86.8).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00991
|
images/Shaft_00991.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø70.1 mm and length at least 301.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø68.1 mm over length 14.7 mm (from Z=0.0 to Z=14.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø68.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø53.9 mm over length 60.2 mm (from Z=0.0 to Z=282.0).\n10. Finish turn diameter Ø34.9 mm over length 46.9 mm (from Z=0.0 to Z=221.8).\n11. Finish turn diameter Ø30.0 mm over length 174.9 mm (from Z=0.0 to Z=174.9).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00342
|
images/Shaft_00342.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø80.3 mm and length at least 223.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø78.3 mm over length 22.9 mm (from Z=0.0 to Z=22.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø78.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø60.6 mm over length 53.3 mm (from Z=0.0 to Z=195.3).\n10. Finish turn diameter Ø44.3 mm over length 114.9 mm (from Z=0.0 to Z=142.0).\n11. Finish turn diameter Ø39.6 mm over length 27.1 mm (from Z=0.0 to Z=27.1).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00308
|
images/Shaft_00308.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø59.7 mm and length at least 128.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø57.7 mm over length 18.4 mm (from Z=0.0 to Z=18.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø57.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø45.0 mm over length 17.8 mm (from Z=0.0 to Z=105.5).\n9. Finish turn diameter Ø39.8 mm over length 40.1 mm (from Z=0.0 to Z=87.7).\n10. Finish turn diameter Ø36.6 mm over length 16.5 mm (from Z=0.0 to Z=47.6).\n11. Finish turn diameter Ø30.0 mm over length 31.1 mm (from Z=0.0 to Z=31.1).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00136
|
images/Shaft_00136.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 70.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 51.6 mm (from Z=0.0 to Z=51.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø29.0 mm over length 14.0 mm (from Z=0.0 to Z=14.0).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00088
|
images/Shaft_00088.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø58.5 mm and length at least 195.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø56.5 mm over length 86.0 mm (from Z=0.0 to Z=86.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø56.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø52.1 mm over length 54.2 mm (from Z=0.0 to Z=104.9).\n10. Finish turn diameter Ø40.4 mm over length 38.7 mm (from Z=0.0 to Z=50.7).\n11. Finish turn diameter Ø33.7 mm over length 12.0 mm (from Z=0.0 to Z=12.0).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00327
|
images/Shaft_00327.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø56.6 mm and length at least 122.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø54.6 mm over length 18.3 mm (from Z=0.0 to Z=18.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø54.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø43.9 mm over length 29.7 mm (from Z=0.0 to Z=98.7).\n9. Finish turn diameter Ø30.0 mm over length 69.0 mm (from Z=0.0 to Z=69.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00475
|
images/Shaft_00475.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø44.8 mm and length at least 233.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø42.8 mm over length 74.7 mm (from Z=0.0 to Z=74.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø42.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø31.5 mm over length 103.5 mm (from Z=0.0 to Z=154.0).\n10. Finish turn diameter Ø30.0 mm over length 50.5 mm (from Z=0.0 to Z=50.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00981
|
images/Shaft_00981.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø53.4 mm and length at least 161.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø51.4 mm over length 37.0 mm (from Z=0.0 to Z=37.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø51.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø33.3 mm over length 28.1 mm (from Z=0.0 to Z=119.2).\n10. Finish turn diameter Ø30.0 mm over length 91.1 mm (from Z=0.0 to Z=91.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00850
|
images/Shaft_00850.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø38.9 mm and length at least 232.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø36.9 mm over length 38.4 mm (from Z=0.0 to Z=38.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø36.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 189.4 mm (from Z=0.0 to Z=189.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00892
|
images/Shaft_00892.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 306.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 242.6 mm (from Z=0.0 to Z=242.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø26.2 mm over length 59.1 mm (from Z=0.0 to Z=59.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00375
|
images/Shaft_00375.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø39.3 mm and length at least 117.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø37.3 mm over length 14.0 mm (from Z=0.0 to Z=14.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø37.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 98.8 mm (from Z=0.0 to Z=98.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00178
|
images/Shaft_00178.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 94.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 60.4 mm (from Z=0.0 to Z=60.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø23.8 mm over length 29.1 mm (from Z=0.0 to Z=29.1).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00026
|
images/Shaft_00026.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø70.1 mm and length at least 67.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø68.1 mm over length 13.5 mm (from Z=0.0 to Z=13.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø68.1 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø59.6 mm over length 5.0 mm (from Z=0.0 to Z=48.5).\n9. Finish turn diameter Ø51.7 mm over length 12.0 mm (from Z=0.0 to Z=43.5).\n10. Finish turn diameter Ø48.0 mm over length 31.5 mm (from Z=0.0 to Z=31.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00349
|
images/Shaft_00349.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø69.0 mm and length at least 312.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø67.0 mm over length 88.3 mm (from Z=0.0 to Z=88.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø67.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø53.1 mm over length 52.0 mm (from Z=0.0 to Z=219.1).\n10. Finish turn diameter Ø49.0 mm over length 39.1 mm (from Z=0.0 to Z=167.1).\n11. Finish turn diameter Ø36.6 mm over length 60.7 mm (from Z=0.0 to Z=128.0).\n12. Finish turn diameter Ø32.9 mm over length 67.3 mm (from Z=0.0 to Z=67.3).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00499
|
images/Shaft_00499.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø58.7 mm and length at least 159.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø56.7 mm over length 65.9 mm (from Z=0.0 to Z=65.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø56.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø50.0 mm over length 16.9 mm (from Z=0.0 to Z=88.2).\n9. Finish turn diameter Ø33.7 mm over length 71.3 mm (from Z=0.0 to Z=71.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00474
|
images/Shaft_00474.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø44.4 mm and length at least 275.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø42.4 mm over length 34.4 mm (from Z=0.0 to Z=34.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø42.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø38.1 mm over length 87.0 mm (from Z=0.0 to Z=236.3).\n10. Finish turn diameter Ø30.0 mm over length 149.3 mm (from Z=0.0 to Z=149.3).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00617
|
images/Shaft_00617.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø61.0 mm and length at least 299.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø59.0 mm over length 34.9 mm (from Z=0.0 to Z=34.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø59.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø48.9 mm over length 84.9 mm (from Z=0.0 to Z=259.9).\n10. Finish turn diameter Ø32.6 mm over length 24.3 mm (from Z=0.0 to Z=175.0).\n11. Finish turn diameter Ø30.0 mm over length 150.7 mm (from Z=0.0 to Z=150.7).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00697
|
images/Shaft_00697.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø65.9 mm and length at least 175.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø63.9 mm over length 52.3 mm (from Z=0.0 to Z=52.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø63.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø58.7 mm over length 36.2 mm (from Z=0.0 to Z=117.9).\n9. Finish turn diameter Ø47.3 mm over length 20.6 mm (from Z=0.0 to Z=81.7).\n10. Finish turn diameter Ø30.0 mm over length 61.1 mm (from Z=0.0 to Z=61.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00050
|
images/Shaft_00050.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø44.4 mm and length at least 236.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø42.4 mm over length 37.6 mm (from Z=0.0 to Z=37.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø42.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø36.5 mm over length 71.7 mm (from Z=0.0 to Z=193.9).\n10. Finish turn diameter Ø30.0 mm over length 122.2 mm (from Z=0.0 to Z=122.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00211
|
images/Shaft_00211.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.0 mm and length at least 317.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 199.0 mm (from Z=0.0 to Z=199.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø24.2 mm over length 113.6 mm (from Z=0.0 to Z=113.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00381
|
images/Shaft_00381.png
|
[
{
"from": "user",
"value": "Generate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø60.7 mm and length at least 114.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø58.7 mm over length 17.3 mm (from Z=0.0 to Z=17.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø58.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø45.5 mm over length 40.7 mm (from Z=0.0 to Z=92.3).\n9. Finish turn diameter Ø30.0 mm over length 51.6 mm (from Z=0.0 to Z=51.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
End of preview. Expand
in Data Studio
Technical Documents: Shafts Process (v1, PNG)
license: cc-by-4.0 pretty_name: Technical Documents: Shafts Process (v1, PNG) language: - en task_categories: - visual-question-answering size_categories: - 1K<n<10K annotations_creators: - machine-generated source_datasets: - original
- ~1000 image→text pairs (stepped shafts → machining process)
- Fixed 10–11 step template; right-side Z=0; tailstock rule (L/D>3 or total length > 190 mm)
- Images converted from SVG to PNG (width 1400px)
Structure
- images/
- annotations/train|val|test.jsonl
Example
{
"id": "Shaft_00668",
"image": "images/Shaft_00668.png",
"conversations": [
{
"from": "user",
"value": "Generate the machining process for the stepped shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø35.4 mm and length at least 70.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø33.4 mm over length 14.4 mm (from Z=0.0 to Z=14.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø33.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 51.1 mm (from Z=0.0 to Z=51.1).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
]
}
- Downloads last month
- 547